Correct use of the torque tester
For the correct use of the torque tester, users of the torque tester should know that improper operation of the torque tester will directly affect the service life of the torque tester, in order to better extend the service life of the torque tester. Torque Tester Xiaobian specially organized the correct use of the torque tester.
Torque tester picture
Torque tester operation:
1. Before using the torque tester, check if the power of the instrument is sufficient. If the battery is insufficient, please charge it first (it can also be used when charging).
2. Turn on the power switch and the displayed torque value is zero. If it is not zero, press the clear key to clear the torque value.
3, before the test, * need to set the upper and lower limits, zui small storage value, zui small peak hold value, automatic peak time, automatic shutdown time, gravity acceleration and so on.
1. Upper limit setting: The user sets the upper limit value and can freely set according to the need. When the upper limit value is reached, the automatic sound and light prompt is displayed, and the upper limit value is not higher than the full scale.
2. Lower limit setting: The user sets the lower limit value and can be freely set according to the need. The lower limit value is the automatic light prompt, and the lower limit value must not be higher than the set upper limit value.
3, zui small storage value setting: the user sets the small storage value of zui according to the storage needs, the data smaller than the value will not be stored.
4, Zui small peak hold value setting: the user according to the peak, automatic peak measurement needs to be freely set, data less than this value is not saved by the peak.
5. Automatic peak time setting: The user can freely set the time required to maintain the peak value according to the automatic peak measurement state from 1 second to 99 seconds.
6. Automatic shutdown time setting: In the no-operation state, the automatic shutdown time can be set freely from 0 minutes to 9 minutes (when set to 0 minutes, it means to cancel the automatic shutdown).
7. Gravity acceleration setting: The user can set the gravity acceleration value according to the position of the area. The machine defaults to 9.794.
8. Restore the initial settings: If the user operates improperly or changes the data multiple times, the data can be restored to the factory state by using this setting.
Torque tester use environment:
1. Pay attention to the humidity and dust in the operating environment. The torque tester is not recommended to be too long in an open environment, especially not to rain; the operating environment is kept dry; the torque tester is used to avoid being close to the heat source.
2. Since there are many cases where there may be a threat of pests and rats, the signal line of the torque tester is exposed to some places, so it is necessary to prevent damage to the pests.
3. In areas where lightning is frequent, or during thunderstorms, reliable lightning arresters or other reliable lightning protection measures must be installed. Sensors and meters are static-sensitive devices. Anti-static measures must be taken during use.
Torque Tester Maintenance:
1. When the torque tester is not used for a long time (such as more than one month), it should be checked according to the environmental conditions to protect it from moisture or other bad gas.
2. Avoid contact with corrosive substances and prolong service life. Non-waterproof platform scales should avoid water in the sensor, junction box, etc., damage or affect the measurement.
3. Regularly clean the rust of the sensor screw to keep the sensor clean and free from interference, so as to avoid changes to the sensor resistance and affect the weighing.
4. Check the position of the angle screw regularly to see if the screw position is in the normal use range.
5. If the torque tester should be powered off quickly, if it can not accurately determine the cause of the fault, please inform the professional engineer of the company to check and organize. The user should not disassemble the chassis at will, and must not replace the internal parts at will; the torque tester operator and Instrument maintenance personnel are required to undergo special training to perform operations and maintenance.
Therefore, understanding the correct use of the torque tester and routine maintenance and maintenance can reduce the damage/maintenance rate. The torque tester naturally prolongs its service life. Shanghai real dry torque tester is worth having!
Vault Room Construction,Vault Room In House,Vault Room Door,Vault Room
Hebei Yingbo Safe Boxes Co.,Ltd , https://www.yingbosafebox.com